BM**B-XASS-TF (LF)(SN) with Kapton tape

 Replace ** with the applicable number of positions / circuits.

JST does not offer the SMT top-entry XA headers with Kapton tape for straight pick-and-place equipment vacuum nozzles. JST suggests the PCB assembler to use a vacuum nozzle with a tip bent at 90° to pick the part out of the tape cavity by one of the side walls of this header.

Alternatively, if possible, mechanical pincers may also be used to extract the header from the tape cavity for placement onto the surface mount pads of the PCB.

What is the recommended PCB hole size for the PH through-hole headers for harder resin boards?

The following are the recommended drill hole sizes for the most common PCB materials:

JST Part Numbers

B*B-PH-K-S  (LF)(SN)
S*B-PH-K-S  (LF)(SN)

Replace "*" with the applicable number of circuits (2 ~ 16).

Recommend PCB hole size (all dimensions are in mm):

Paper-based epoxy resin

Ø0.70 ~ 0.75 for 2 circuits
Ø0.75 ~ 0.80 for 3 ~ 16 circuits

Glass-based epoxy resin (without through-hole)

Ø0.70 ~ 0.75 for 2 circuits
Ø0.75 ~ 0.80 for 3 ~ 16 circuits

Note: Hole size of the paper-based epoxy PC board and glass-based epoxy resin PC board
(without through hole) is the value set for the drill hole (NC processing).

Glass-based epoxy resin (with through-hole)

Ø0.80 ~ 0.85 for 2 circuits
Ø0.85 ~ 0.90 for 3 ~ 16 circuits

Note: Hole size of glass-based epoxy PC board (with through-hole) is the finished dimension
after plating through-hole.

If further information is required please contact your local authorized JST sales rep which can be found at the following URL:

http://www.jst.com/home5.html

Is there a 22AWG contact for the PH series?

Yes. There is a contact for the PH series that will work for 22AWG wire. The part number is SPH-001T-P0.5S. It has an AWG range of 26 to 22 with an insulation outer diameter range of 0.9 to 1.5mm. For 26 and 24 AWG, JST suggests using UL1007 wire. For 22AWG, we suggest UL1061 or UL1571.

Difference between CZ header with and without (V) suffix

Enacted in January 2004, the (V) indicates a configuration change made to the top-entry headers to step-up flowability of the molding process and improve productivity and stability. The change does not affect performance of the connector. Below are schematics showing the revision.

 

Without the (V) suffix

With the (V) suffix

B**B-PNISK-1A(LF)(SN)(F): Difference without (F) suffix

The difference between part number B**B-PNISK-1A(LF)(SN)(F) and the same without the (F) suffix is the wafer material. It is the part with the (F) that can only be purchased. It is the same glass-filled PA66, UL94V-0 material as called out on our data sheet online: http://www.jst-mfg.com/product/pdf/eng/ePNI.pdf

Replace ** with the applicable number of circuits.

What is your ECCN?

The ECCN for JST Corporation and JST Sales America, Inc. is EAR99.

How do you order B**B-ZR-SM4-TF (LF)(SN) with Kapton tape (suction cap)?

The ordering part number would be B**B-ZR-SM4-TFT  (LF)(SN). Where "**" is replace with the applicable number of circuits.

For additional questions please contact us here: Connector Technical Assistance